Homemade Air Conditioner

Components of a Homemade Air Conditioner:








Essentially what we’ll be doing is using the power of evaporative cooling and a fan to bring down the temperature in your room. In this case we’ll be using ice water stored in a cooler that will then cycle through a copper loop in front of a box fan. I’ll leave it to you to head to wikipedia to read up on how the process works, it’s not unlike you sweating to cool down. Myself I’ve done enough sweating so I’ll let the air conditioner do it for me. (Note: this is the perfect project to do some scrounging and modify your design and tailor to whatever you may have on hand that would fulfill the same function). Okay for this project you’ll need to assemble the following components:


A Fan (box fan is ideal)
A cooler (you could use a Styrofoam cooler or whatever cooler you may have on hand)
An aquarium pump (or a pond pump, the higher the Gallons Per Hour the more cooling you’ll get mine is a 132 GPH, also be sure your pump has enough power to push the water to the height required to reach the top of your coil)
Copper coil tubing (the particular type of tubing I used was 3/8″ outer diameter copper coil – 20 feet)
Vinyl tubing (my pump called for 1/2″ Inner Diameter tubing about 10 feet worth. Hopefully you get better tubing then I did I believe mine is the autokink brand)
Reducers and fittings to connect your copper coil to your vinyl tubing and ultimately to your pump. If you are unsure a conversation with a hardware store plumbing expert should get you going in the right direction. They were terribly excited about my project so they were glad to help. (I used 2 1/2″ to 3/8″ couplers that were then fitted with 5/8″ threaded couplers and then screwed in two 1/2″ barbed brass adapters to connect the tubing, finally I used 3 1″ hose clamps to firm it all up)
Wood for making box fan outriggers
Zip ties for attaching the tubing to your fan





Assemble the Air Conditioner:













  1. First you need to get the copper tubing laid out and get your fittings in place. It was a simple matter of 6 screws holding the protective screen on my box fan so I was able to easily remove it and use it for laying out the copper tubing. Since the copper tubing was already coiled it was a simple matter to gradually and carefully bend it into  a spiral. Give yourself some room between each circle for more surface area.
  2. Attach the fittings to the copper tubing. In my case I needed to solder the joints between the copper tubing and the fittings. You might be able to find some solderless compression type fittings depending on your materials and hardware store availability. That would certainly speed things along and would allow you to avoid having to sweat the fittings together with some form of torch. I prepared all the fittings by sanding the copper tubing and reaming the fittings. I then applied some solder flux to the inside of the fitting and the outside of the tubing. I then proceeded to heat the fitting with my torch until it was hot enough to melt the solder, then I applied the solder. Repeat this for the the other end of the tubing.
  3. Now that the fittings were in place I screwed in the barbed adapters for my vinyl hose after applying some Teflon tape to the threads.
  4. The vinyl tubing slipped over the barbs and then I added two screw-type clamps to the barbs.
  5. The pump had a special adapter that I inserted into the vinyl tubing and then again used a screw clamp to secure the tubing.
  6. Now is a good time to test your setup for leaks. Fill your cooler with some water, submerge the pump and connect the tubing to your pump. You then run the other tubing back into the cooler. Fire it up and make sure it works like you expect.
  7. Now you need to attach the copper tubing to your fan screen. This is a simple process, just plan where you want your tubing to enter and leaveyour setup and then start attaching it with the zip ties. I put about 4 for each circle for good holding power. You can also fine tune your coiling as you go.
  8. Once you’re done attaching the tubing to the screen you might want to build your self some outriggers for your fan. Mine was a bit tipsy to begin with so I cut up part of a 2×4 about 16 inches long and screwed to the bottom of my box fan.  
  9. Reattach the fan screen with the original screws
  10. Now you need to figure out how you are going to get your vinyl tubing into your cooler. You’ll need 3 holes, 1 for the inlet to the copper tubing, 1 for the outlet and 1 for the pump power cord. I had a drill bit the same size as my vinyl tubing so it was a straight forward process, just make sure it’s in the lid or at the top of the cooler, obviously you don’t want water leaking out.
  11. Okay you should be ready to give her a try.



Operating the Air Conditioner:




Alright you’re going want to put your fan and cooler in place, get your tubing cabled appropriately and you’ll want to get some form of pan or something underneath your fan to catch the condensation from the coil. Fill your cooler with enough water to cover the pump and then put in a bunch of ice. I used 3 bags to start. Turn on the pump and adjust the fan speed. Now bask in the coolness of your own evaporative cooler.

This sucker does go through the ice so you’ll want to do something other than buy hundreds of bags of ice. I took a variety of containers, yogurt, cottage cheese, paint buckets, etc and made larger blocks, they seem to last longer. Some alternate methods instead of straight ice are 2 liter bottles filled with salt water. They last longer and are colder than standard ice. You’ll just want to keep the salt water sealed so that you are not cycling it through your setup. Also you could use the freezer blocks that you can reuse. Good luck and stay cool.

Comments

Popular Posts